How To Shine Tactical Boots
Police, military service members, and other tactical operators are expected to sport mirror-finish tactical boots. Even if you aren't required to shine your tactical shoes, there's nothing more polished than a spit-shine finish. The experts at 5.11 Tactical® weighed in to create this easy, step-by-step guide on how to shine tactical boots for formal events and daily wear so you can always put your best foot forward.
SUPPLIES YOU NEED FOR THAT SPIT-SHINE LOOK
Before you start shining your tactical boots, give yourself some room to work – this process can get a little messy. Grab an old bedsheet, towel, or shop rag and cover your workspace in case you have a shoe polish catastrophe.
Then, gather all the materials you need:
- Rubbing alcohol
- Shine brush (preferably made from horsehair, which is less likely to damage your boots)
- Polishing cloths (100-percent cotton is the way to go)
- Wax shoe polish
- Cotton balls and cotton-tipped applicators
STEP-BY-STEP INSTRUCTIONS TO SHINE TACTICAL BOOTS
STEP 1: PREP YOUR BOOTS
To get the perfect shine, you need a good foundation. Prepare your boots for polish by removing dust, dirt, and debris from the upper and sole using the horsehair brush. Slightly dampen a horsehair brush – not one with synthetic bristles that can scratch your boot’s surface – and use gentle, back-and-forth motions to brush away any particles that shouldn’t be there.
STEP 2: APPLY A BASE COAT
If your boots already have a base coat, fast-forward to Step 3: Polish Your Boots. If not, use the following steps to give your tactical boots a solid base coat:
- Apply a thick layer of polish in small, circular motions with a soft cloth.
- Let the base coat dry for 15 minutes.
- Thoroughly brush the boot or vigorously scrub it with a clean, dry cotton cloth to remove excess polish. Don’t expect a great shine yet – a base coat smooths out the leather’s bumps and irregularities so you can get a spit-shine finish later.
- Let the base coat dry for another 5 minutes before moving on to the final step.
STEP 3: POLISH YOUR BOOTS
After prepping your boots and allowing the base coat to absorb, follow these steps to finish shining your tactical boots:
- Wrap the tips of your index and middle fingers with a soft, clean, dry cotton cloth. Pick up a small amount of polish with your covered fingers, and apply the polish with small, circular motions all over the boot, picking up more polish whenever necessary.
- Complete the previous step on the other boot. Switching back and forth between boots allows each boot to dry between steps.
- Dampen a new clean cotton cloth in water, wring it out, and wrap it around your index and middle fingers as before. Dampening the cloth prevents it from absorbing polish. For an old-fashioned spit shine, you can use your own saliva instead of water.
- With the damp cloth wrapped around your fingers, pick up a small amount of polish and rub it into the boot using small, circular motions. When the polish turns grey or stops transferring to your boot, shift your fingers to a new part of the cloth, pick up more polish, and repeat until you've covered the entire boot.
- Switching back and forth between boots, apply six or seven coats of polish with the dampened cloth, re-dampening as necessary. You’ll see the boot’s hazy shine become glossier and more even each time you add a new layer of polish.
- After all the polish is dry, use a clean, dry cloth made from cotton or nylon to buff your boots.
- Finally, stare at yourself in your perfectly shined tactical boots and pat yourself on the back for a job well done.
EXPERT TIPS FOR SHINING TACTICAL BOOTS
Keep in mind that your tactical boots need a smooth foundation with a thick base coat before you’ll get a mirror shine. These instructions on how to shine tactical boots need to happen in the right order or you won’t get the gleaming finish you’re after.
Here are a few other things to remember when it comes to polishing tactical boots:
- Use small, circular motions in every step.
- Work with the thinnest layer of polish possible.
- The first shine is always the hardest – after that, you’ll have a solid base coat and the process will become faster and easier.